plasterers.tradePost a job

Guide

Plasterboard types: which board goes where, and how thick

Standard board for dry rooms, moisture-resistant board for kitchens and bathrooms, fire-rated board where a fire rating is specified. On a ceiling, 9.5mm board suits joists up to 400mm apart; wider spacing needs thicker board.

A room under construction with boarded walls

The main types

Plasterboard is a gypsum core between two paper faces, and the variations change what the core can cope with. Board is classified under the European standard BS EN 520 by letter, and the letter is printed on the back of every sheet along with the maker and thickness.

BoardUsual colourWhere it goes
Standard wallboard (Type A)Grey or ivory faceWalls and ceilings in dry rooms
Moisture resistant (Type H)GreenKitchens, bathrooms, utility rooms
Fire resistant (Type F)Pink or redWhere a fire rating is specified
Acoustic (higher density)BlueWalls and floors where sound matters
Insulated (thermal laminate)Foam backingLining cold outside walls
Impact resistantVaries by makerHallways, stairs, busy areas

The colours are a convention that most makers follow, not a rule. Read the print on the back rather than trusting the colour of the paper.

Moisture resistant does not mean waterproof

Green board has a water-repellent additive in the core and a treated paper face. British Gypsum describes its moisture-resistant board as suitable for intermittent moisture, such as kitchens, bathrooms and sheltered external soffits. That covers a bathroom wall that gets steamy, and a wall behind a basin or bath that takes the odd splash.

It does not cover the inside of a shower enclosure, which is wetted every day. There, most tilers fix a cement-based or foam tile backer board, or tank the wall with a waterproofing system before tiling. Using green board behind a shower and tiling straight onto it is a common cause of a wall that softens behind the tiles.

Fire-rated board

Fire board has glass fibre and other additives in the core that hold it together for longer in a fire. It is used where the building regulations require a wall, ceiling or steel to resist fire for a set time: walls and ceilings between a garage and the house, protected stairways in a loft conversion, and boxing around a new steel beam are typical examples.

The required rating and how many layers make it up are set by the design and checked by building control. One sheet of pink board does not by itself make a wall fire-rated; the studs, the joints, the screws and any gaps round services are part of the system.

Thickness: walls and ceilings

The common thicknesses are 9.5mm, 12.5mm and 15mm. On walls, 12.5mm is the usual board on stud partitions and the one most partition systems are designed around. On ceilings, the thickness has to match how far apart the joists are. Siniat's drywall manual gives these maximum joist centres for board fixed directly to timber joists:

Board thicknessJoist centres, no intermediate noggingsWith intermediate noggings
9.5mm400mm450mm
12.5mm or 15mm450mm600mm

Noggings round the perimeter are needed in every case. A ceiling boarded in 9.5mm across joists at 600mm centres will sag between them, and that sag shows as a wave under the light long before it cracks.

Edges: square or tapered

Tapered edge board has a shallow dip along its long edges so that tape and jointing compound can fill the joint flush with the face. It is made for tape and joint finishing, where the board paper stays as the surface.

Square edge board is intended for skimming, where the whole sheet gets a coat of plaster and the joints are scrimmed. In practice plasterers skim tapered board all the time without trouble. What matters more is that the person buying the board knows which finish the wall is getting.

How it is fixed

On timber or metal studs and on ceiling joists, board is screwed with drywall screws at the spacing the board maker sets, closer at the edges than in the middle of the sheet. Screw heads sit just below the paper face without tearing it, because a screw driven through the paper holds nothing.

On brick or block walls, board is usually fixed by dot and dab: dabs of adhesive on the wall, the board pressed onto them and tapped flat. It is quick and evens out an uneven wall, but it leaves a hollow behind the board that matters later when you come to hang anything heavy.

What to ask whoever is boarding

  • Which board are you using in each room, and is it moisture-resistant anywhere near water?
  • What is going behind the shower, and how is it being waterproofed?
  • Does any of this wall or ceiling need a fire rating, and who has specified it?
  • What thickness on the ceiling, and what are the joist centres?
  • Is it being skimmed, or taped and jointed, and to what finish level?

Common questions

Is green plasterboard waterproof?

No. It is moisture resistant, made for intermittent moisture such as a steamy bathroom or a splashback area. Inside a shower enclosure a cement-based or foam backer board, or a tanking system, is the usual choice.

Can I use standard plasterboard in a bathroom?

It is not a good idea on walls near the bath, basin or shower. Moisture-resistant board costs little more and copes far better with the humidity of a bathroom.

What thickness plasterboard for a ceiling?

It depends on the joist spacing. 9.5mm suits joists at up to 400mm centres. At 600mm centres use 12.5mm or 15mm board, with noggings between the joists.

What is the difference between pink and green plasterboard?

Pink is fire-rated board with additives that hold the core together in a fire. Green is moisture-resistant board for humid rooms. Some boards combine both, so check the print on the back.

Where to go from here

Plasterboarding and dry lining by town

Read next

Find a plasterer near you