plasterers.tradePost a job

Guide

Mist coat on new plaster: the ratio, the paint, the method

A mist coat is cheap matt emulsion thinned with water, commonly around three parts paint to one part water, rolled onto plaster that has dried right through. It soaks in, seals the surface and gives the topcoats something to grip.

An empty room with bare walls and a wooden floor

What a mist coat is for

Fresh gypsum plaster is extremely absorbent. Put a full-strength emulsion straight onto it and the plaster pulls the water out of the paint faster than the paint can bond. The film dries on the surface, sits there rather than sinking in, and comes away later, often in long strips when somebody puts masking tape on it or the first time the room gets steamy.

A thinned first coat solves that. Because it is mostly water it soaks into the face of the plaster instead of skinning over it, and once dry it leaves an evenly sealed surface with a consistent suction. The two topcoats that follow then bond to paint rather than to bare plaster, which is the whole point.

The ratio

There is no single correct figure, because paints differ. Common trade mixes run from about four parts paint to one part water at the thick end to something closer to half and half at the thin end. Three parts paint to one part water is the middle of that range and a sensible starting point.

Two things override any rule of thumb. The first is the tin: many trade emulsions print their own thinning instructions for new plaster, and some are sold specifically for bare plaster and go on unthinned. The second is how the coat behaves on the wall. It should soak in and dry to a slightly patchy, chalky look. If it sits on the surface and dries with a sheen, it is too thick. If it runs down the wall in streams, it is too thin.

Which paint to use

PaintFor a mist coat?
Contract or trade matt emulsionYes, the usual choice
Emulsion sold for bare new plasterYes, follow the tin, often unthinned
Vinyl matt or vinyl silkNo, the vinyl sits on the surface
One-coat or stain-blocking emulsionNo, not made to soak in

White is easiest because it shows the defects you will want to fix before the topcoats. It also does not need to match the final colour, which is why most decorators buy the cheapest large tub of contract matt they can find.

When to put it on

Only when the plaster is dry all the way through. A skim changes colour from a dark pinkish brown to an even pale cream as it dries, and that colour change is your signal. The last patches to turn are usually in corners, behind doors and low down on outside walls.

In a warm, ventilated room a skim usually gets there in three to seven days; a backing coat underneath adds a week or more. Painting over damp patches traps the water behind the paint, and it comes back as dark shadows and flaking. Our drying times guide covers what speeds this up and what ruins it.

How to apply it

  • Sheet the floor. A thin mix spatters far more than normal emulsion.
  • Lightly rub over the wall with a fine abrasive pad or a sanding block to knock off any nibs, then brush the dust away.
  • Cut in round the edges and corners with a brush.
  • Roll the rest in sections, working quickly so each area is rolled into wet paint.
  • Let it dry fully, normally a few hours, but check the tin.
  • Walk the room with a torch held flat to the wall and fill any small dents or hairline cracks the mist coat has shown up.
  • Two full-strength topcoats.

The mist coat will look patchy and thin. That is normal and not a reason to add another heavy coat.

Common mistakes

Rushing it is the big one: the room looks finished, the colour change is nearly complete, and the topcoat goes on a few days early.

The next is mixing it too thick to save time, which defeats the point and produces exactly the peeling the thin coat was meant to prevent. Using a vinyl paint has the same effect. Going the other way and thinning it so much that it is mostly water leaves a dusty surface that still has not been sealed, and the topcoats soak in unevenly.

Plasterboard that has been taped and jointed rather than skimmed is a different surface. The paper face and the jointing compound absorb paint at different rates, so a drywall primer or the sealer the paint maker recommends usually gives a more even result than a watered emulsion.

Common questions

Do I need a mist coat on new plaster?

Yes, unless the paint you are using is sold for bare new plaster and says it goes straight on. Full-strength ordinary emulsion on fresh plaster tends to peel later because it never properly bonded.

How many mist coats should I do?

One is usually enough. On very absorbent plaster or a large patched area that has soaked up the first coat unevenly, a second thin coat helps before the topcoats.

Can I mist coat a ceiling the same way?

Yes. The mix and the method are the same, though a thinner coat spatters more overhead, so cover everything below and wear eye protection.

Can I fill cracks after the mist coat?

Yes, and it is a good time to find them, because the paint shows up dents and hairlines that bare plaster hides. Fill, sand lightly, spot the filled areas with the mist mix, then topcoat.

Where to go from here

Plastering and skimming by town

Read next

Find a plasterer near you