Guide
Is my wall load bearing? The checks, and who confirms it
What sits above the wall, which way the joists run and what it is built from all point to the answer, but only a structural engineer can confirm it. Removing a load bearing wall needs building control approval.

What load bearing means
A load bearing wall carries weight from above down to the foundations: the ends of floor joists, a wall on the floor above, or loads from the roof. Some walls also brace the building sideways without carrying much weight at all. Take either kind out without replacing what it was doing and the floor or ceiling above it sags, cracks and can ultimately fail.
Nobody can tell you for certain by looking at the room. The checks below tell you which way the evidence points, and they are worth doing before you ask anyone to price the work, because they change what kind of job it is.
The checks you can make yourself
- Look at the joists above. In the loft for a top floor wall, or under a lifted floorboard for a downstairs one. Joists running across the top of the wall and resting on it, or joining over it, are a strong sign it is carrying them. Joists running parallel to it suggest it is not, though not always.
- Look at what is directly above. A wall on the next floor that sits exactly on top of this one is often being held up by it.
- Knock on it. A hollow sound means a timber or metal stud wall; a dull solid one means brick or block. Masonry walls inside a house are more likely to be structural.
- Find where it is. A wall running down the middle of the house front to back, the spine wall, is commonly load bearing in older houses.
- Look for the original plans. The council's building control department may hold records for houses built or altered in recent decades, and a builder's or developer's drawings sometimes survive with the deeds.
Why a hollow wall can still be structural
Most modern stud partitions carry nothing but themselves, and that leads people to assume any hollow wall can come out. It is the most dangerous assumption on this page.
In older houses, timber stud partitions were often built to carry the floor above, and some are trussed so that they hold up the ceiling joists across a span. In newer houses, a stud wall may be helping to brace the roof structure or the building as a whole. Hollow tells you what it is made of. It does not tell you what it does.
What the rules say
In England, the Planning Portal says that removing a load bearing wall needs building control approval because it alters the structure of the house, and that you will need a report from a structural engineer with structural calculations. That approval comes from your council's building control service or a registered building control approver.
Removing a wall that is not load bearing will likely not need building control approval, provided it does not affect fire escape routes, ventilation, drainage or electrics. The Planning Portal still recommends an engineer's report beforehand to confirm the wall is not structural.
Planning permission is not normally needed for internal walls, but a listed building needs listed building consent for significant work inside as well as out. And in England and Wales, if a new beam has to be seated into a wall shared with a neighbour, cutting into that party wall is work you must tell them about under the Party Wall Act.
What the job involves when it is structural
The wall is replaced by a beam, steel or engineered timber, sized by the engineer. The floor above is propped temporarily while the wall comes out, the beam sits on padstones at each end, and building control inspects at the stages they set.
Then comes the part people forget to budget for, which is making good. The beam is usually boxed in with plasterboard, sometimes fire-rated board if building control requires it, and skimmed. The ceiling either side, the wall ends and the floor where the wall stood all need patching, and the cleanest finish is often a full skim of the ceiling across the opening.
Taking out a stud wall that is not structural
Once an engineer has confirmed it is not structural, a non-load bearing stud wall comes out quickly. The electrics in it are isolated and moved first by an electrician, then the boards and studs are stripped, and the head and sole plates are taken off the ceiling and floor.
That leaves strips of damaged plaster along the ceiling and the adjoining walls. A plasterer patches these and usually skims the ceiling so the line where the wall was does not show under a low light.
Common questions
Can a stud wall be load bearing?
Yes. Many timber partitions in older houses carry the floor above, and some in newer houses brace the roof. A hollow sound tells you what the wall is made of, not whether it is structural.
Who can tell me if a wall is load bearing?
A structural engineer. A builder or plasterer can give an opinion, but building control will want the engineer's report and calculations for a structural wall, and the Planning Portal recommends one even for a wall you believe is not.
Do I need building regulations approval to remove an internal wall?
For a load bearing wall, yes. For a non-load bearing wall, usually not, as long as removing it does not affect escape routes, ventilation, drainage or electrics.
Do I need planning permission to knock through?
Not normally, because internal alterations are not development that needs planning permission. A listed building is the exception: significant internal work needs listed building consent.