Guide
Can you plaster over paint, tiles, wallpaper or Artex?
Yes over sound paint, once it is cleaned, keyed and primed with a bonding coat. Wallpaper comes off first, tiles nearly always do, and a textured ceiling from before 2000 gets tested before anyone scrapes it.

Surface by surface
A skim coat is two or three millimetres thick and has no strength of its own. It is exactly as good as whatever it is stuck to, so the question is never really whether plaster will go over something. It is whether that something will stay on the wall once it is carrying the plaster.
| Surface | Skim over it? | What happens first |
|---|---|---|
| Sound matt emulsion | Yes | Wash it, then a grit-loaded bonding primer |
| Gloss, eggshell or vinyl silk | Yes, with more work | Sand the sheen off, then the bonding primer |
| Flaking or chalky paint | Not yet | Scrape back to a firm edge, then prime |
| Wallpaper or lining paper | No | Strip it |
| Ceramic tiles | Rarely | Take them off, or board over them |
| Plasterboard | Yes | Scrim tape on the joints, skim the whole board |
| Artex or textured coating | Usually | Test if pre-2000, never sand, skim or overboard |
Painted walls: the tape test
Paint is the most common surface a plasterer skims over, and on a sound wall it is routine. What fails is paint that was already letting go of the wall underneath, because the new coat adds weight and water to a film that was barely holding on.
You can check this yourself in a minute. Press a strip of masking tape firmly onto the paint in two or three places, including a corner and somewhere near the skirting, and rip it off sharply. Clean tape means the paint is well bonded. Flakes of paint on the tape mean that patch is coming off the wall, and it has to be scraped back before anything goes over it.
Gloss and silk paints are sound but slippery. Wet plaster needs a key, and a shiny film gives it none, so the sheen is sanded off and a grit-loaded bonding primer goes on. The grit is the point: it gives the skim something mechanical to hold, which is why most plasterers prefer it on painted walls to a coat of watered down PVA.
Wallpaper and tiles
Wallpaper is the request plasterers turn down most often, and they are right to. The water in the wet plaster soaks through the paper into the paste, the paste softens, and the paper lets go of the wall with the new skim attached to it. It can happen on the day or months later as a bubble. Stripping is unskilled work, and doing it yourself before the plasterer arrives is the cheapest part of the job.
Glazed ceramic tiles have almost no suction and a smooth face, which makes them a very difficult background for plaster. Specialist primers exist, but most plasterers will either take the tiles off or fix plasterboard over them. Taking them off usually pulls patches of the old plaster with them, so expect some backing coat on top of the skim. Boarding over them is faster and costs you the thickness of the board on that wall.
Artex and other textured coatings
This is the one that needs care before anybody touches it. HSE says asbestos can be found in any home built or refurbished before 2000, and it names textured decorative coatings such as Artex as one of the places it turns up. A coating put on before then may or may not contain it, and the only way to know is to have a sample tested.
HSE's advice to homeowners is to leave asbestos materials where they are if they are in good condition, and not to repair or remove them yourself without training. So the actions to avoid on an untested ceiling are sanding it, scraping it dry, or knocking the peaks off with an abrasive.
None of that stops you plastering. A shallow texture can be skimmed over with a bonding coat and two passes of finish, which buries it without disturbing it. A heavy swirl is usually overboarded: new plasterboard screwed through into the joists and skimmed, with the old coating sealed behind it. Our Artex guide goes through the testing and the options in more detail.
What to ask before the work starts
A plasterer quoting over an existing surface should be able to answer these on the phone or on a site visit:
- What do you think this surface is, and is it sound enough to skim?
- Which bonding primer will you use on the paint?
- If the paint lifts when you prime it, what happens to the price?
- Is stripping paper or removing tiles in the quote, or is that mine to do?
- On a textured ceiling: has it been tested, and if not, why are we deciding now?
The third question matters more than it looks. A wall that seemed sound and starts lifting under the primer is a common reason for a one day skim turning into a second visit.
Common questions
Can you plaster over gloss paint?
Yes, once the sheen has been sanded off and a grit-loaded bonding primer applied. Plaster needs a key, which a shiny film does not give, so skipping the sanding is how a skim ends up coming away in sheets.
Do I need PVA before skimming over paint?
Most plasterers now use a grit-loaded bonding primer on painted walls instead of diluted PVA, because the grit gives a mechanical key. Ask which they use; either way the paint underneath has to be sound.
Can you skim over Artex without removing it?
Yes, if the pattern is shallow and the coating is sound. A bonding coat and two passes of finish bury it without disturbing it. A deep pattern is normally overboarded instead. If it predates 2000 and has not been tested, nobody should be sanding it.
Can you plaster over tiles in a bathroom?
Not usually. Tiles are too smooth and too non-absorbent to hold a skim reliably. They are taken off, which means some patching of the plaster behind, or boarded over with a moisture-resistant board and skimmed.